| Část Ne | Výrobcem | Aplikace |
|---|
| MAX6309UK39D4-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.803(min),3.998(max) Nominal timeout period 1120ms. |
| MAX6317HUK31BZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX1450CAP | MAXIMIC | Low-cost, 1%-accurate signal conditioner for piezoresistive sensors. |
| MAX4221CSA | MAXIMIC | Dual,SPDT, 2-input, single-output switch. 330MHz -3dB bandwidth. |
| MAX3299CUE | MAXIMIC | 3.0V to 5.5V, 2.5Gbps LAN laser driver. |
| MAX508ACPP | MAXIMIC | Voltage-output, 12-bit DAC with internal reference. 8+4 data-bus widths. Error +-1/2. |
| MXD1000SA250 | MAXIMIC | 5-tap silicon delay line |
| MAX1204AEAP | MAXIMIC | +5V, 8-channel, serial, 10-bit ADC with 3V digital interface, INL (LSB) +1/2 |
| MAX802MEPA | MAXIMIC | Microprocessor supervisory circuit. 4.40V precision supply-voltage monitor. Power-fail accuracy guaranteed to +-2%. |
| MAX6320PUK25AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| IH5042CWE | MAXIMIC | General-purpose CMOS analog switch. Single pole, double throw (SPDT) |
| MAX211ECWI | MAXIMIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX262AMRG | MAXIMIC | Microprocessor programmable universal active filter. Accuracy 1%. |
| IH5045C/D | MAXIMIC | General-purpose CMOS analog switch. Dual, double pole, single throw (Dual DPST) |
| REF02AZ | MAXIMIC | +5V precisioon voltage reference. Max TEMPCO 8.5ppm/degC. Initial error +-15mV |
| MAX884EPA | MAXIMIC | 3.3V or adjustable, low-dropout, low current, 200mA linear regulator. 1microA(max) shutdown(OFF) mode. |
| MAX6328UR25-T | MAXIMIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 2.500V. Order increment 10k |
| MAX603CPA | MAXIMIC | 5V or adjustable, low-dropout, low quiescent currrent, 500mA linear regulator. |
| MAX5176AEEE | MAXIMIC | Low-power, serial, 12-bit DAC with voltage output. Single-supply +3V operation. Full-scale output range +4.096V(Vref=+2.5V). INL(LSB) +-2. |
| MAX6379XR35-T | MAXIMIC | Ultra-low-power voltage detector, 3.5V |
| MAX4539CWP | MAXIMIC | Low-voltage, single 8-to-1 calibration multiolexer. |
| MAX6314US39D2-T | MAXIMIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 3.90V. Reset timeout period(min) 20ms. |
| MAX5253BMJP | MAXIMIC | +3V, quad, 12-bit, voltage-output DAC with serial interface. INL(LSB) +-2. |
| MAX5101AEUE | MAXIMIC | +2.7V to 5.5V, low-power, triple, parallel 8-bit DAC with Rail-to-Rail voltage output. INL (LSB) +-1 |
| MAX334EJE | MAXIMIC | High speed quad SPST analog switch |
| MAX7705EPA | MAXIMIC | Microprocessor power-supply monitor with reset |
| MXD1210CPA | MAXIMIC | Nonvolatile RAM controller |
| MAX114CNG | MAXIMIC | 5 V, 1Msps, 4-channel, 8-bit ADC |
| MAX6316MUK32DW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MXD1013C/D080 | MAXIMIC | 3-in-1 silicon delay line. Output delay 80ns. |
