| Část Ne | Výrobcem | Aplikace |
|---|
| MAX186DCAP | MAXIMIC | Low-power, 8-channel, serial 12-bit ADC. |
| MX7502KN | MAXIMIC | Low-power, monolithic, CMOS analog multiplexer. |
| MAX128ACAI | MAXIMIC | Multirange, +5V, 12-bit DAS with 2-wire serial interface. INL(LSB) +1/2,-1/2 |
| MAX4051AEPE | MAXIMIC | Low-voltage, CMOS analog multiplexer |
| MAX488ECPA | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX806RCSA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX6432EIUS-T | MAXIMIC | 3.5 V, Low-power, single/dual-level battery monitor with hysteresis |
| MX7523JN | MAXIMIC | CMOS 8 bit multiplying D/A converter. Error 1/2LSB |
| MAX6306UK34D2-T | MAXIMIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.315(min),3.485(max) Nominal timeout period 20ms. |
| MX584JESA | MAXIMIC | Pin programmable precision voltage reference. Error +-30mV. |
| MAX144BC/D | MAXIMIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-1 |
| MAX6316MUK50CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX4204ESA | MAXIMIC | Ultra-high-speed 780MHz -3dB bandwidth, 280MHz 0.1dB gain flatness, low-noise, low-power, open-loop buffer. |
| MX7541ASQ | MAXIMIC | CMOS 12 bit multiplying D/A converter. Error 1 LSB. |
| MAX6318LHUK49DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 1.12sec, typ watchdog timeout 25.6sec |
| MAX6318MHUK37DX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MX7528UD | MAXIMIC | CMOS dual 8 bit buffered multiplying DAC. +5V to 15V single supply operation. Error +-1/2 LSB. |
| MAX494CSD | MAXIMIC | Quad, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp. |
| MAX6309UK35D1-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.413(min),3.588(max) Nominal timeout period 1ms. |
| MX7847AQ | MAXIMIC | Complete, dual, 12-bit multiplying DAC. 12-bit parallel interface. Error (LSB) +-1 |
| MAX1248BMJE | MAXIMIC | +2.7V to 5.25V, low-power, 4-channel, serial 10-bit ADC. INL (LSB) +1,-1 |
| MAX878MJA | MAXIMIC | Step-up/step-down DC-DC converters |
| MAX3869E/D | MAXIMIC | +3.3V, 2.5Gbps, SDH/SONET, laser driver with gurrent monitor and APC. |
| OP37CZ | MAXIMIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX6319MHUK36D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1120ms |
| MAX6319MHUK42D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 1120ms |
| MAX6318MHUK31DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6328XR27-T | MAXIMIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 2.700V. Order increment 10k |
| MAX4426MJA | MAXIMIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX6318MHUK45BZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
