Cesta:okDatasheet > Semiconductor list > MaximIC Datasheet > MaximIC-100

6316LUK28CZ-T MAX4508MJE MAX3235ECWP MAX182ACWI MAX3680EAI MAX3864D MX7828TQ MAX6336US23D2-T MAX6310UK32D1-T MAX469EWE MAX500BEWE MAX6502CMP055-T MAX803MEXR-T MAX8868C/D30 MAX4275BJESA MAX6322HPUK27A-T MAX483EEPA MAX491ESD MAX6320PUK43CX-T MAX322EPA MXD1005PD200 MAX4053ACPE DS185

MaximIC Letáky katalog-100

Část NeVýrobcemAplikace
MAX6317HUK38AW-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 1ms, typ watchdog timeout 6.3ms
MAX6316LUK28CZ-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 140ms, typ watchdog timeout 25.6sec
MAX4508MJE MaximICFault-protected, high-voltage single 8-to-1 multiplexer.
MAX3235ECWP MaximIC+-15kV ESD-protected, 1microA, 250kbps, 5.0V, dual RS-232 with internal capacitor.
MAX182ACWI MaximICCalibrated 4-channel 12-bit ADC with T/H and reference.
MAX3680EAI MaximIC622Mbps, +3.3V, SDH/SONET 18 deserializer with TTL outputs.
MAX3864D MaximIC+3 to +5.5 V, 2.5 Gbp wide dynamic range transimpedance preamplifier
MX7828TQ MaximICCMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1
MAX6336US23D2-T MaximICUltra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 2.3V, reset timeout(min) 20ms.
MAX6310UK32D1-T MaximICMultiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.120(min),3.280(max). Nominal timeout period 1ms.
MAX469EWE MaximICTwo-channel, triple video buffer. Voltage gain 2V/V.
MAX500BEWE MaximICCMOS, quad, serial-interface 8-bit DAC. Error(LSB) +-2.
MAX6502CMP055-T MaximICLow-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) +55.
MAX803MEXR-T MaximICMicroprocessor reset circuit Reset threshold 4.38V. Open-drain active-low reset. 2.5k increments.
MAX8868C/D30 MaximICLow-noise, low-dropout, 150mA linear regulator with auto-discharge function. Preset output voltage 3.00V
MAX4275BJESA MaximICDual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 49, 1+ (Rf/Dg) noninverting gain 50, -3dB BW 310kHz.
MAX6322HPUK27A-T MaximICMicroprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 1ms
MAX483EEPA MaximIC+-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32.
MAX491ESD MaximICLow-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32.
MAX6320PUK43CX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms
MAX322EPA MaximICPrecision, dual-supply, SPTS analog switch.
MXD1005PD200 MaximIC5-tap silicon delay line
MAX4053ACPE MaximICLow-voltage, CMOS analog switch
DS1859B-020 MaximICDual, temperature-controlled resistors with internally calibrated monitors, 20KOhm
MAX6375UR30-T MaximICUltra-low-power voltage detector, 3.0V
MAX1480BEPI MaximICComplete, isolated RS-485/RS-422 data inteface.
MX536AJD MaximIC1V. Auxiliary dB output 60dB range. Low power 1.2mA(typ).
MAX6319LHUK29A-T MaximICMicroprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1ms
MAX6310UK41D4-T MaximICMultiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.998(min),4.203(max). Nominal timeout period 1120ms.
MAX233EPP MaximIC+5V-powered, multichannel RS-232 driver-receiver.

<< 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 >>