| Část Ne | Výrobcem | Aplikace |
|---|
| MAX6141EUR | MaximIC | Low-cost, low-dropout, 3-terminal voltage reference. Preset output voltage 4.096V. |
| MAX6306UK46D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.514(min),4.746(max) Nominal timeout period 140ms. |
| MAX358EPE | MaximIC | Fault-protected analog 8 channel single-ended (1 of 8) multiplexer. |
| MAX1247BCPE | MaximIC | +2.7V, low-power, 4-channel, serial 12-bit ADC. INL (LSB) +1,-1 |
| ICL7663CSA | MaximIC | Programmable positive voltage regulator |
| MAX4566C/D | MaximIC | Two dual SPST switches, low-voltage, bidirectional RF/video switch. |
| MAX808MESA | MaximIC | Supervisory circuit with +-1.5% reset accuracy. Reset threshold(typ) 4.425V. CMOS RAM write protection.. |
| MXD1005PD100 | MaximIC | 5-tap silicon delay line |
| MAX692AMJA | MaximIC | Microprocessor supervisory circuit. 4.40V precision supply-voltage monitor |
| MAX163BEWG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX267ACWG | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX6307UK39D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.803(min),3.998(max).Nominal timeout period 140ms. |
| MX7501JN | MaximIC | Low-power, monolithic, CMOS analog multiplexer. |
| MAX6307UK35D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.413(min),3.588(max).Nominal timeout period 20ms. |
| MX7524CQ | MaximIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/8 LSB |
| MAX328CPE | MaximIC | Ultra-low lealage monolithic CMOS analog multiplexer. |
| MAX6320PUK43DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX954EUA | MaximIC | Ultra low-power, single-supply Op Amp + comparator. Op Amp gain stability 10V/V. Supply current 5microA. |
| MAX6317HUK37AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.700V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX369CWN | MaximIC | Fault-protected analog multiplexer with latch. 4 channel differential (2 of 8). |
| MX7548JP | MaximIC | CMOS 8-bit microprocessor compatible 12-bit DAC. Linearity +-1 LSB. |
| MX7624MJE | MaximIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +12V to +15V. Error +-1/2 LSB |
| MAX2233EEE | MaximIC | 900MHz ISM-band, 250mW power amplifier with analog or digital gain control. |
| MAX804RC/D | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX7400CSA | MaximIC | 8-th-order, lowpass, elliptic, switched-capacitor filter. Filter response elliptic (r=1.5), operating voltage +5V |
| MAX6005EUR-T | MaximIC | Low-cost, low-power, low-dropout, voltage reference. Output voltage 5.000V, input voltage (Vout+200mV) to 12.6V. |
| MAX4538EPE | MaximIC | Quad, low-voltage, SPST analog switches with enable. 2 NO and 2 NC. |
| MAX6316LUK41AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX942MJA | MaximIC | Dual, high-speed, low-power, 3V or 5V single-supply, Rail-to-Rail comparator |
| MAX9041AEUT-T | MaximIC | Micropower, single-supply operation +2.5V to 5.5V, single comparator + precision reference IC. |
