| Část Ne | Výrobcem | Aplikace |
|---|
| MXD1000SE175 | MaximIC | 5-tap silicon delay line |
| MAX6313UK41D1-T | MaximIC | "Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.998(min) 4.203(max).Nominal timeout period 1ms." |
| MAX9004ESD | MaximIC | "Low-power, high-speed, single-supply op amp + comparator + reference IC. Op-Amp gain stability 10V/V. Op-Amp gain bandwidth 8MHz. Shutdown mode." |
| MAX146BMJP | MaximIC | "+2.7 V, low-power, 8-channel, serial 12-bit ADC. INL(LSB) +-1." |
| MAX640CPA | MaximIC | "3.3V or adjustable, high-efficiency, current-limiting PFM control scheme, step-down DC-DC converter." |
| OP27FZ | MaximIC | Low-noise precision operational amplifier. 8MHz gain-bandwidth product. 2.8V/micros slew rate |
| MAX6317HUK40BX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 20ms, typ watchdog timeout 102ms" |
| MAX6315US46D3-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.63V. Reset timeout period(min) 140ms. |
| MAX220CPE | MaximIC | "+5V-powered, multichannel RS-232 driver-receiver." |
| MAX6316MUK45DZ-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 1120ms, typ watchdog timeout 25.6sec" |
| MAX824MEUK | MaximIC | Microprocessor supervisory circuit. Reset threshold 4.38V. Active-low reset. Active-high reset. Watchdog input. |
| MAX190BENG | MaximIC | "Low-power, 12-bit sampling ADC with internal reference and power-down. Error(LSB) +-1." |
| MAX4275AOESA | MaximIC | "Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 9, 1+ (Rf/Dg) noninverting gain 10, -3dB BW 640kHz." |
| MAX6316MUK27AZ-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.700V, min reset timeout 1ms, typ watchdog timeout 25.6sec" |
| MAX163BENG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX635ACSA | MaximIC | "Preset -5V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 5%." |
| MAX208ECWG | MaximIC | "+-15kV ESD-protected, +5V RS-232 transceiver" |
| MAX1459CAP | MaximIC | "2-wire, 4-20 mA smart signal conditioner." |
| MAX691ACPE | MaximIC | Microprocessor supervisory circuit. Reset threshold(typ) 4.65V. |
| MAX6321HPUK25CY-T | MaximIC | "Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec" |
| MAX6316LUK40AW-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1ms, typ watchdog timeout 6.3ms" |
| MAX6316LUK30BW-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 20ms, typ watchdog timeout 6.3ms" |
| MAX306MJI | MaximIC | "Precision, 16-channel, high-performance, CMOS analog multiplexer" |
| MAX508AEPP | MaximIC | "Voltage-output, 12-bit DAC with internal reference. 8+4 data-bus widths. Error +-1/2." |
| MAX186CEWP | MaximIC | "Low-power, 8-channel, serial 12-bit ADC." |
| MAX6378UR40-T | MaximIC | "Ultra-low-power voltage detector, 4.0V" |
| MAX6316LUK39DX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1.12sec, typ watchdog timeout 102ms" |
| MAX6318MHUK25DX-T | MaximIC | "Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms" |
| MAX1240BESA | MaximIC | "+2.7V, low-power, 12-bit serial ADCs in 8-pin SO. INL (LSB) +1" |
| MAX4550EAI | MaximIC | "Serrially controlled, dual 4x2, clickless audio/video crosspoint switches." |
