| Část Ne | Výrobcem | Aplikace |
|---|
| MAX6317HUK44AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX6316MUK48CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX6346XR33-T | MAXIMIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 3.300V. Order increment 10k |
| MAX6321HPUK26DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6314US42D3-T | MAXIMIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.20V. Reset timeout period(min) 140ms. |
| MAX6316LUK46BW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX6317HUK34CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX1450C/D | MAXIMIC | Low-cost, 1%-accurate signal conditioner for piezoresistive sensors. |
| MAX8215CPD | MAXIMIC | +-5V, +-12V dedicated microprocessor voltage monitor. |
| MAX6316MUK36BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX6319MHUK30B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 20ms |
| MAX4044ESD | MAXIMIC | Single/dual/quad, low-cost, micropower rail-to-rail I/O op amp. |
| MAX353CSE | MAXIMIC | Precision, quad, SPST analog switch |
| MAX232AESE | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX520AEPE | MAXIMIC | Quad, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1. |
| MAX6312UK41D1-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.998(min) 4.203(max). Nominal timeout period 1ms. |
| DG444CJ | MAXIMIC | Improved, quad, SPST analog switch |
| MAX6316MUK49CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX6321HPUK33CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX1487EESA | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MAX172BCNG | MAXIMIC | Complete 10 microsec. CMOS 12-bit ADC. Error +- 1 LSB. |
| MX565AJN | MAXIMIC | High speed 12-bit monolithic D/A converter. High stability buried zener 10V reference. Error +-1/2LSB |
| MAX1480AEPI | MAXIMIC | Complete, isolated RS-485/RS-422 data inteface. |
| MAX6316LUK31AX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX6319LHUK49B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 20ms |
| MAX6317HUK30AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 1ms, typ watchdog timeout 1.6ms |
| MAX634EPA | MAXIMIC | CMOS micropower inverting switching regulator |
| MAX1694EUB | MAXIMIC | USB current-limited switch with fault blanking |
| MX3554SM | MAXIMIC | Wideband fast-settling operational amplifier |
| MAX6318MHUK41CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
