| Část Ne | Výrobcem | Aplikace |
|---|
| MAX6337US21D2-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 2.1V, reset timeout(min) 20ms. |
| MAX6808UR26-T | MaximIC | Voltage detector. Reset output active-low, open-drain. Threshold reset 2.6V |
| MAX192AEAP | MaximIC | Low-power, 8-channel, serial 10-bit ADC. Error(LSB) +-1/2. |
| MAX3223ECPP | MaximIC | +-15kV ESD-protected, 1microA, 3.0 to 5.5V, 250kbps, RS-232 transceiver with AutoShutdown. |
| MAX6378UR45-T | MaximIC | Ultra-low-power voltage detector, 4.5V |
| MAX6318MHUK27CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX5355EPA | MaximIC | 10-bit voltage-output DAC. +3.3V single supply operation. |
| MX7534SQ | MaximIC | Microprocessor-compatible, 14-bit DAC. INL +-2 LSB. |
| MAX437MJA | MaximIC | Low noise, high-precision op amp. 60MHz gain-bandwidth product. |
| MAX6504CMN035-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) -35. |
| MAX407MJA | MaximIC | 1.2microA max, dual, single-supply op amp. |
| MAX6306UK38D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.705(min),3.895(max) Nominal timeout period 20ms. |
| MAX6310UK42D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.095(min),4.305(max). Nominal timeout period 1ms. |
| MAX6321HPUK30DY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX4274AOEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 9, 1+ (Rf/Dg) noninverting gain 10, -3dB BW 640kHz. |
| MAX805TCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MAX6318MHUK46CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX821SUS-T | MaximIC | Microprocessor voltage monitor with pin-selectable power-on reset timeout delay (1ms,max, 20ms,min or 100ms,min). Reset threshold(nom) 2.93V. Active-low reset output. |
| MXD1000SE25 | MaximIC | 5-tap silicon delay line |
| MX7575KEQP | MaximIC | CMOS, microprocessor-compatible, fast conversion time 5 microsec, 8-bit ADC. INL +-1/2 LSB. |
| MAX491EEPD | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6316MUK31BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX503ENG | MaximIC | 5V, low-power, parallel-input, voltage-output 10-bit DAC. |
| DG387BWE | MaximIC | General purpose CMOS dual analog switch. |
| MAX825TEUK | MaximIC | Microprocessor supervisory circuit. Reset threshold 3.08V. Active-low reset. Active-high reset. Manual reset input. |
| MAX6318LHUK40DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.000V min, reset timeout 1.12sec,typ watchdog timeout 102ms |
| MAX230EPP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| ICL8069CMSQ2 | MaximIC | Low-voltage reference, 50 ppm/C - max temp. coefficient. |
| MX7847SQ | MaximIC | Complete, dual, 12-bit multiplying DAC. 12-bit parallel interface. Error (LSB) +-1 |
| MAX829EUK | MaximIC | Switched-capacitor voltage inverter. 35kHz. +1.5V to +5.5V input voltage range. |
