| Část Ne | Výrobcem | Aplikace |
|---|
| MAX500ACWE | MaximIC | CMOS, quad, serial-interface 8-bit DAC. Error(LSB) +-1. |
| MAX6316MUK47DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.700V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MX7245SQ | MaximIC | Complete, 12-bit voltage-output DAC. |
| MAX232ACPE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6320PUK41DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX3265C/D | MaximIC | 3.0V to 5.5V, 2.5Gbps limiting amplifier. |
| MAX3244ECAI | MaximIC | +-15kV ESD-protected, 1microA, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus. |
| MAX463C/D | MaximIC | Two-channel, triple RGB switch and buffer. Voltage gain 1V/V. |
| MAX6315US38D4-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 3.80V. Reset timeout period(min) 1120ms. |
| MAX394CWP | MaximIC | Precision, quad, SPST analog switch |
| ICL7652CTV | MaximIC | Chopper-stabilized operational amplifier |
| MAX805LESA | MaximIC | Microprocessor supervisory circuit. 4.65V precision supply-voltage monitor |
| MAX821RUS-T | MaximIC | Microprocessor voltage monitor with pin-selectable power-on reset timeout delay (1ms,max, 20ms,min or 100ms,min). Reset threshold(nom) 2.63V. Active-low reset output. |
| MAX6320PUK31CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6318MHUK28BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX4249EUB | MaximIC | Dual, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 22MHz, min stable gain 10V/V, with shutdown mode. |
| MAX3082ESA | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX6309UK48D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.680(min),4.920(max) Nominal timeout period 1120ms. |
| MAX4074ALEUK-T | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 5V/V, noniverting gain 6V/V, -3dB BW 71kHZ. |
| MAX6307UK38D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.705(min),3.895(max).Nominal timeout period 20ms. |
| MAX6310UK27D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 2.633(min),2.768(max). Nominal timeout period 20ms. |
| MAX4052AEEE | MaximIC | Low-voltage, CMOS analog multiplexer |
| MAX6316MUK34BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX3266CSA | MaximIC | 1.25Gbps, 3V to 5.5V, low-noise transimpedance preamplifier for LANs. |
| MAX526CMYG | MaximIC | Calibrated quad, 12-bit, voltage-output DAC. INL(LSBs) +-1/2. Fast output settling 3micros. |
| MAX6317HUK45AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX701CPA | MaximIC | Power-supply monitor with reset. |
| MAX1614C/D | MaximIC | High-side,N-channel MOSFET switch driver |
| MAX6321HPUK38DW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX6806XR23-T | MaximIC | Voltage detector. Reset output active-low, push-pull. Threshold reset 2.3V |
