Cesta:okDatasheet > Semiconductor list > MaximIC Datasheet > MaximIC-52

JA MAX6316MUK50DZ-T MAX6317HUK32CX-T DG442DJ MAX6713SEXS-T10 MAX759C/D MAX6318MHUK39DY-T DG529AZ MAX506BCWP MAX4174ABEUK-T MAX6316MUK44CY-T MAX490CSA MAX875BCSA MAX900BCPP MAX630ESA MAX6317HUK43CX-T MAX876BCPA MAX4663CPE MXD1013C/D012 MAX6316MUK37CY-T MAX4592EUE MAX4127C/D MAX466

MaximIC Letáky katalog-52

Část NeVýrobcemAplikace
MAX810MEUR-T MaximICMicroprocessor reset circuit. Reset threshold 4.38V. Push-pull active-high reset. 2.5k increments.
MAX492MJA MaximICDual, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp.
MAX6316MUK50DZ-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 1120ms, typ watchdog timeout 25.6sec
MAX6317HUK32CX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 140ms, typ watchdog timeout 102ms
DG442DJ MaximICImproved, quad, SPST analog switch
MAX6713SEXS-T10 MaximICMicroprocessor reset circuit with manual reset input. Reset threshold 2.93V. Output type active-low open-drain reset.
MAX759C/D MaximICAdjustable, inverting carrent-mode PWM regulator.
MAX6318MHUK39DY-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec
DG529AZ MaximIC8-channel latchable multiplexer
MAX506BCWP MaximICQuad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-3/2 LSB.
MAX4174ABEUK-T MaximICSingle, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 0.25, 1+ (Rf/Dg) noninverting gain 1.25, -3dB BW 1700kHz.
MAX6316MUK44CY-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 140ms, typ watchdog timeout 1.6sec
MAX490CSA MaximICLow-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 300 microA. Number of transmitter on bus - 32.
MAX875BCSA MaximICLow-power, low-drift precision voltage reference. 5V+-3.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC.
MAX900BCPP MaximICHigh-speed, low-power voltage comparator
MAX630ESA MaximICCMOS micropower step-up switching regulator
MAX6317HUK43CX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 140ms, typ watchdog timeout 102ms
MAX876BCPA MaximICLow-power, low-drift precision voltage reference. 10V+-5.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC.
MAX4663CPE MaximIC2.5om, quad, SWPST, CMOS analog switch (two NC and two NO switches).
MXD1013C/D012 MaximIC3-in-1 silicon delay line. Output delay 12ns.
MAX6316MUK37CY-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.700V, min reset timeout 140ms, typ watchdog timeout 1.6sec
MAX4592EUE MaximICHigh-speed, single-supply 12V, quad, SPST analog switches (four NO switches).
MAX4127C/D MaximICDual, wide-bandwidth, low-power, single-supply Rail-to-Rail I/O op amp. BW 5MHz.
MAX4665CPE MaximIC5om, quad, SPST, CMOS analog switch (four NO switches).
MAX6315US46D1-T MaximICOpen-drain microprocessor reset circuit. Reset threshold(nom) 4.63V. Reset timeout period(min) 1ms.
MAX6312UK39D1-T MaximICMultiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.803(min) 3.998(max). Nominal timeout period 1ms.
MAX810SEUR-T10 MaximICMicroprocessor reset circuit. Reset threshold 2.93V. Push-pull active-high reset. 10k increments.
MAX187AEWE MaximIC+5V, low-power, 12-bit serial ADC. Error(LSB) +-1/2.
ICL7650MJA MaximICChopper-stabilized amplifier
MAX793RCSE MaximICMicroprocessor supervisory circuit. Reset threshold 2.55V to 2.70V. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Battery OK output.Watchdog input.Manual reset inp.

<< 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 >>