| Část Ne | Výrobcem | Aplikace |
|---|
| MAX9050BEUK-T | MaximIC | Micropower, single-supply, single comparator + precision reference IC. |
| MAX4066EPD | MaximIC | Low-cost, low-voltage, quad, SPTS, CMOS analog switch. |
| MAX6318MHUK50CY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6316MUK35BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| ICL7622BMJD | MaximIC | Dual operational amplifier, 5mV |
| MAX753CSE | MaximIC | CCFL backlight and LCD contrast controller. Negative LCD contrast. |
| MAX4275ADEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 1, 1+ (Rf/Dg) noninverting gain 2, -3dB BW 590kHz. |
| MAX6318MHUK49DW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX2421EAI | MaximIC | 900 MHz image-reject transceiver. |
| MAX4581ASE | MaximIC | Low-voltage, CMOS analog multiplexer (8-channel). |
| MX7528JN | MaximIC | CMOS dual 8 bit buffered multiplying DAC. +5V to 15V single supply operation. Error +-1 LSB. |
| MAX333AEPP | MaximIC | Precision, quad, SPDT, CMOS analog switch. |
| MAX6315US47D4-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.70V. Reset timeout period(min) 1120ms. |
| MAX5250ACPP | MaximIC | Low-power, quad, 10-bit, voltage-output DAC with serial interface. INL(LSB) +-1/2. |
| MAX1092ACEG | MaximIC | 400ksps, +5V, 4-channel single-ended/2-channel pseudo-differential, 10-bit ADCs with +2.5V reference and parallel interface. INL (LSB) 0.5 |
| MAX404ESA | MaximIC | Video operational amplifier. |
| MAX6321HPUK28CX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX8867EUK50-T | MaximIC | Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 5.00V |
| MAX6334UR19D2-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.9V, reset timeout(min) 20ms. |
| MAX8873REUK-T | MaximIC | Low-dropout, 120mA linear regulator. Preset output voltage 2.80V. |
| MAX4551EPE | MaximIC | +-15kV ESD-protected, quad, low-voltage, SPST analog switches (four NC switches). |
| MAX122BEWG | MaximIC | 500ksps, 12-bit ADCs with track/hold and reference, INL (LSBs) +1 |
| MAX197BENI | MaximIC | Multi-range (+10V, +5V, +10V, +5V), single +5V, 12-bit DAS with 8+4 bus interface |
| MAX552ACPA | MaximIC | +3V, 12-bit, serial, multiplying DAC. Linearity(LSB) +-1/2. |
| MXD1000UA45 | MaximIC | 5-tap silicon delay line |
| MAX5183BEEI | MaximIC | Dual, 10-bit, 40MHz, current/voltage simultaneous-output DAC. |
| MAX6358MTUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 3.08V (Vcc3). Active-low open-drain reset. Watchdog timer. |
| MAX6318LHUK42BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.200V min, reset timeout 20ms,typ watchdog timeout 6.3ms |
| MAX6316MUK45BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX4074AEEUK-T | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 1.25V/V, noninverting gain 2.25V/V, -3dB BW 70kHZ. |
