| Část Ne | Výrobcem | Aplikace |
|---|
| MXD1000C/D175 | MaximIC | 5-tap silicon delay line |
| MAX6306UK48D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.680(min),4.920(max) Nominal timeout period 20ms. |
| MAX174BEPI | MaximIC | Industry standard complete 12-bit A/D converter. 8 microsec. max conversion time. Linearity (LSBs) 1/2. TEMPCO(ppm/C) 38. |
| MAX4391EJA | MaximIC | CMOS micropower inverting switching regulator |
| MAX383ESE | MaximIC | Precision, low-voltage analog switch. |
| MAX743EPE | MaximIC | Dual-output, switch-mode regulator (+5V to +/-15V or +/-12V) |
| MAX973CUA | MaximIC | Ultra-low-power, open-drain, dual comparator. Internal precision reference 1%. Internal hysteresis yes. |
| MAX4275ANEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 8, 1+ (Rf/Dg) noninverting gain 9, -3dB BW 480kHz. |
| MAX6314US46D1-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.63V. Reset timeout period(min) 1ms. |
| MAX6310UK37D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.608(min),3.793(max). Nominal timeout period 1120ms. |
| MAX6317HUK50DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| DG302CK | MaximIC | Dual, TTL compatible CMOS analog switch. |
| MX7225BQ | MaximIC | CMOS quad 8-bit D/A converter with double-buffered logic inputs. Error +-2 LSB. |
| MAX6318MHUK25CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX264ACWI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX519BC/D | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
| MAX1660EEE | MaximIC | Digitally controlled fuel-gauge interface |
| MAX6319MHUK35A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1ms |
| MAX6316MUK43DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
| MAX6318LHUK42AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.200V min, reset timeout 1ms,typ watchdog timeout 25.6sec |
| MAX817LCUA | MaximIC | +5V microprocessor supervisory circuit. Reset threshold 4.65V, active-low reset, backup-battery switchover, power-fail comparator, watchdog input, battery freshness seal. |
| MAX264ACPI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX6250AESA | MaximIC | Low-noise, precision, +5V output voltage reference. Max TEMPCO (ppm/C) 3.0. |
| MX7524JCSE | MaximIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/2 LSB |
| MAX5184BEEG | MaximIC | 10-bit, 40MHz, current/voltage-output DAC. |
| MAX6363HUT46-T | MaximIC | Low-power microprocessor supervisory circuit with battery-on output. Reset threshold(typ) 4.63V. Active-high push-pull reset. |
| MAX534BCEE | MaximIC | 5V, low-power, 8-bit quad DAC with Rail-to-Rail output buffer. INL (LSB) +-2 |
| MAX6319LHUK30D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1120ms |
| MAX6317HUK49BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX6316MUK42DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
