| Část Ne | Výrobcem | Aplikace |
|---|
| MAX4066CSD | MaximIC | Low-cost, low-voltage, quad, SPTS, CMOS analog switch. |
| MAX6351LTUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.63V (Vcc5) and 3.08V (Vcc3). Active-low push-pull reset output 5V and 3V. |
| ICL7126CPL | MaximIC | Low power, 3 1/2 digit A/D converter |
| MAX908MJD | MaximIC | Dual, high-speed, ultra low-power, single 4.4V to 5.5V supply operation TTL comparator. |
| MAX6326XR28-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 2.800V. Order increment 10k |
| MAX355MJE | MaximIC | Fault-protected analog multiplexer |
| MAX6321HPUK35BY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MXD1000PD100 | MaximIC | 5-tap silicon delay line |
| MX7506KQ | MaximIC | Single, 16 channel (1 of 16) monolithic CMOS analog multiplexer. |
| MAX6363LUT26-T | MaximIC | Low-power microprocessor supervisory circuit with battery-on output. Reset threshold(typ) 2.63V. Active-low push-pull reset. |
| MAX6320PUK26BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX6316LUK31DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 1.12sec, typ watchdog timeout 25.6sec |
| MXL1014CN | MaximIC | Quad precision op amp. |
| MAX6307UK42D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds4.095(min),4.305(max).Nominal timeout period 140ms. |
| DG211C/D | MaximIC | Quad SPST CMOS analog switch. |
| ICL7652BIJD | MaximIC | Chopper-stabilized operational amplifier |
| MAX4426CPA | MaximIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX6309UK38D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.705(min),3.895(max) Nominal timeout period 1120ms. |
| MAX537AEPE | MaximIC | Calibrated, quad, 12-bit voltage-output DAC with serial interface. +-5V supply operation. INL (LSB) +-1/2 |
| MAX814KCPA | MaximIC | +-1% accuracy, low-power, microprocessor supervisory circuit. Reset trip threshold (min) 4.75V (max) 4.85V, push-pull active-low reset output, push-pull active-high reset output, manual reset, power-fail monitor, low-line detector. |
| MAX763AMJA | MaximIC | Step-down, current-mode PWM DC-DC controller. Input voltage range 3.3V to 11V |
| MAX1202BC/D | MaximIC | +5V, 8-channel, serial, 12-bit ADCs with 3V digital interface, INL (LSB) +1 |
| MAX188BEPP | MaximIC | Low-power, 8-channel, serial 12-bit ADC. |
| MAX8868EUK33-T | MaximIC | Low-noise, low-dropout, 150mA linear regulator with auto discharge function. Preset output voltage 3.30V |
| MAX639CSA | MaximIC | 5V or adjustable, high-efficiency, current-limiting PFM control scheme, step-down DC-DC converter. |
| MAX6320PUK38DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX4075AHESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 2.5V/V, noninverting gain 3.5V/V, -3dB BW 116kHz. |
| MAX6378UR46-T | MaximIC | Ultra-low-power voltage detector, 4.6V |
| MAX800MESE | MaximIC | Microprocessor supervisory circuit. Reset threshold(typ) 4.4V. Guaranteed power-fail accuracy to +-2% |
| MAX6318LHUK43CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.300V min, reset timeout 140ms,typ watchdog timeout 102ms |
