| Část Ne | Výrobcem | Aplikace |
|---|
| MAX145BEUA | MaximIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-1. |
| MAX323CPA | MaximIC | Precision, single-supply, SPST analog switch. |
| MAX4075BJESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 49V/V, noninverting gain 50V/V, -3dB BW 50kHz. |
| MF10BWP | MaximIC | Dual universal switched capacitor filter. |
| DG307ABK | MaximIC | CMOS dual and quad analog switch. |
| MAX4174AOEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 9, 1+ (Rf/Dg) noninverting gain 10, -3dB BW 640kHz. |
| MAX6318LHUK48AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX820LCSE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V. Reset and low-line threshold accuracy +-2% |
| MAX6316LUK44BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX4615CSD | MaximIC | Low-woltage, high-speed, quad, SPST, CMOS analog switch has four NC switches. |
| DG390C/D | MaximIC | General purpose CMOS dual analog switch. |
| MAX485ESA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6318LHUK32CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.200V min, reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX218CAP | MaximIC | 1.8V to 4.25V - powered, true RS-232 dual transceiver. |
| MAX473C/D | MaximIC | Single, 10MHz single-supply op amp. |
| MAX6320PUK37BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.700V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MAX809REUR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 2.62V. Push-pull active-high reset. 10k increments. |
| MXD1005PA200 | MaximIC | 5-tap silicon delay line |
| MAX4603CPE | MaximIC | Low on-resistance (2.5om max), quad, SPST, CMOS analog switches (two NO and two NC switches). |
| MAX6318LHUK28BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.800V min, reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX4304EUK-T | MaximIC | Low-noise, low-distortion op amp. Bandwidth 740MHz. Minimum stable gain 2V/V. |
| MAX149ACPP | MaximIC | +2.7V to +5.25V, low-power, 8-channel, serial 10-bit ADC. INL(LSB) +-1/2. |
| MAX6321HPUK50BW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| ICM7556MJD | MaximIC | Dual general purpose RC timer |
| MAX5035DUPA | MaximIC | 1A, 76V, high-efficiency MAXPower step-down DC-DC converter, adj output |
| MX7228KCWG | MaximIC | CMOS octal 8-bit D/A converter. Error +-2 LSB |
| MAX1241BC/D | MaximIC | +2.7V, low-power, 12-bit serial ADCs in 8-pin SO. INL (LSB) +1 |
| MAX9698CSE | MaximIC | Single very fast TTL output comparator |
| MAX4074ACEUK-T | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 0.5V/V, noninverting gain 1.5V/V, -3dB BW 136kHZ. |
| MAX6321HPUK30CW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
