| Část Ne | Výrobcem | Aplikace |
|---|
| MAX4552CSE | MaximIC | +-15kV ESD-protected, quad, low-voltage, SPST analog switches (four NO switches). |
| MAX5003CEE | MaximIC | High-voltage PWM power-supply controller. |
| MAX6318MHUK43DY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX6306UK44D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.270(min),4.490(max) Nominal timeout period 1120ms. |
| MXD1000SE35 | MaximIC | 5-tap silicon delay line |
| MAX632BCPA | MaximIC | CMOS fixed +12V output voltage, adjustable output with 2 resistors step-up switching regulator. 10% output accuracy. |
| MAX6306UK49D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.778(min),5.023(max) Nominal timeout period 1ms. |
| MAX131EQH | MaximIC | 3 1/2 Digit A/D converter with bandgap reference |
| MAX294CWE | MaximIC | 8th-order, lowpass, elliptic, switched-capacitor filter. Clock-tunable corner-freguency range 0.1Hz to 25kHz |
| MAX801LMJA | MaximIC | Supervisory circuit with +-1.5% reset accuracy. Reset threshold(typ) 4.675V. Watchdog. |
| MAX409BESA | MaximIC | 1.2microA max, single, single-supply op amp. |
| MAX942C/D | MaximIC | Dual, high-speed, low-power, 3V or 5V single-supply, Rail-to-Rail comparator |
| DG211CSE | MaximIC | Quad SPST CMOS analog switch. |
| MAX6316LUK50BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 5.000V, min reser timeout 20ms, typ watchdog timeout 1.6sec. |
| MAX6319MHUK45A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1ms |
| MAX445CPG | MaximIC | Low-cost, high-resolution, 200MHz video CRT driver. |
| MAX6318MHUK31CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6318LHUK26CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.630V min, reset timeout 140ms, typ watchdog timeout 1.6sec |
| MX7531KD | MaximIC | CMOS 12 bit multiplying D/A converter. Error 0.1% |
| MAX4427EJA | MaximIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX731CPA | MaximIC | 5V step-up current-mode DC-DC converter |
| MAX6318MHUK34BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX533AEEE | MaximIC | 2.7V, low-power, 8-bit quad DAC with Rail-to-Rail output buffer. INL (LSB) +-1 |
| MAX6313UK32D1-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.120(min) 3.280(max).Nominal timeout period 1ms. |
| MAX5250BCPP | MaximIC | Low-power, quad, 10-bit, voltage-output DAC with serial interface. INL(LSB) +-1. |
| MAX367C/D | MaximIC | Signal-line circuit protector. |
| MAX4278ESA | MaximIC | 310MHz -3dB bandwidth, gain of +2, closed-loop buffer. |
| MAX197AEAI | MaximIC | Multi-range (+10V, +5V, +10V, +5V), single +5V, 12-bit DAS with 8+4 bus interface |
| MAX519BEPE | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
| MAX266BEPI | MaximIC | Pin and resistor programmed universal active filter. Accyracy 2% |
