| Část Ne | Výrobcem | Aplikace |
|---|
| MAX901AESE | MaximIC | High-speed, low-power voltage comparator |
| MAX4667ESE | MaximIC | 2.5om, quad, SPST, CMOS analog switch (two NC switches). |
| MAX6317HUK26DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MAX6317HUK25DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.500V, min reset timeout 1120ms, typ watchdog timeout 102ms |
| MAX4556EPE | MaximIC | Force-sense switches (three indepedent SPDT switches, of which one is a force switch and two sense switches). |
| MAX6316LUK34AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX6316LUK29BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX268BMRG | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 2%. |
| MAX3486EEPA | MaximIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 2.5Mbps. Supply voltage 3.0V to 3.6V |
| MAX1487ESA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MAX4622CSE | MaximIC | Low on-resistance 3om(typ), 5om(max), dual, SPDT, analog switch has two NO and two NC poles. |
| MAX972EPA | MaximIC | Ultra-low-power, open-drain, dual comparator. Internal precision reference none. Internal hysteresis no. |
| MAX3238CAI | MaximIC | +3.0V to +5.5V, 1microA, up to 250kbps, true RS-232 transceiver with autushutdowd plus. |
| DG387CJ | MaximIC | General purpose CMOS dual analog switch. |
| MAX6360SYUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 2.93V (Vcc5) and 2.19V (Vcc3). Active-low push-pull reset 3V. Watchdog timer. Standard version. |
| MAX132CWG | MaximIC | +,- 18-Bit ADC with serial interface |
| OP27EP | MaximIC | Low-noise precision operational amplifier. 8MHz gain-bandwidth product. 2.8V/micros slew rate |
| MAX5464EXT | MaximIC | 2-wire digital potentiometer, 50KOm |
| MAX6316MUK42BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX3222CWN | MaximIC | 3.0V to 5.5V, low-power, up to 1Mbps, true RS-232 transceiver using four 0.1microF external capacitor. Low supply current 300microA. Guaranteed data rate 120kbps. |
| MAX6310UK31D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.003(min),3.157(max). Nominal timeout period 140ms. |
| DG302BWE | MaximIC | Dual, TTL compatible CMOS analog switch. |
| MXD1013PD040 | MaximIC | 3-in-1 silicon delay line. Output delay 40ns. |
| MAX6316MUK32AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX515CSA | MaximIC | 5V, low-power, voltage-output, serial 10-bit DAC. Operate from single +5V supply. 140microA supply current. |
| MAX6318LHUK50CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX805SESA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MAX4075BEESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 24V/V, noninverting gain 25V/V, -3dB BW 120kHz. |
| MAX6321HPUK45DX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX4567EPE | MaximIC | Dual SPDT switches, low-voltage, bidirectional RF/video switch. |
