| Část Ne | Výrobcem | Aplikace |
|---|
| MX574AKN | MaximIC | Industry standard complete 12-bit A/D converter. 25 microsec. max conversion time. Linearity (LSBs) 1/2. TEMPCO(ppm/C) 27. |
| MAX4662CWE | MaximIC | 2.5om, quad, SWPST, CMOS analog switch (four NO switches). |
| MAX7415CUA | MaximIC | 5th-order, lowpass, elliptic, switched-capacitor filter. Transition ratio r = 1.25, operating voltage +3V |
| MAX2660EUT-T | MaximIC | 400MHz to 2.5GHz upconverter mixer. |
| MAX6321HPUK36DW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| OP37BJ | MaximIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX4181ESA | MaximIC | =1. |
| MAX4274BDEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 20, 1+ (Rf/Dg) noninverting gain 21, -3dB BW 300kHz. |
| MAX2663EUT-T | MaximIC | 400MHz to 2.5GHz upconverter mixer. |
| MAX4515EUK | MaximIC | Low-voltage, low-on-resistance, SPST, CMOS analog switch. Normally closed (NC), +2V to +12V single-supply operation. |
| MAX6317HUK29BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX4053EEE | MaximIC | Low-voltage, CMOS analog switch |
| MAX6319MHUK41D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1120ms |
| MAX618EEE | MaximIC | 28V, PWM, step-up DC-DC converter. |
| MAX5352BEUA | MaximIC | Low-power, 12-bit voltage-output DAC with serial interface. INL (LSB) +-1. +5V single-supply operation. |
| MAX6316LUK27AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.700V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX632BC/D | MaximIC | CMOS fixed +12V output voltage, adjustable output with 2 resistors step-up switching regulator. 10% output accuracy. |
| MAX199AEAI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX6504UKP005-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) +5. |
| MAX397CAI | MaximIC | Precision, dual 8-channel, low-voltage, CMOS analo0g multiplexer. |
| MAX923CSA | MaximIC | Dual micropower, low-voltage comparator. Intarnal 1.182V+-1% voltage reference. Internal programmable hysteresis. |
| MAX369EWN | MaximIC | Fault-protected analog multiplexer with latch. 4 channel differential (2 of 8). |
| MAX3083EPD | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX6312UK45D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 4.388(min) 4.613(max). Nominal timeout period 1ms. |
| MX7543JN | MaximIC | CMOS serial input 12 bit DAC. Error +1 LSB. |
| MX7535KEWI | MaximIC | Microprocessor-compatible, 14-bit DAC. INL +-1 LSB. |
| MAX389CPN | MaximIC | High-voltage, fault-protected analog multiplexer. 4-channel differential (2 of 8). |
| REF01HSA | MaximIC | +10V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-50mV |
| MAX500BEPE | MaximIC | CMOS, quad, serial-interface 8-bit DAC. Error(LSB) +-2. |
| MXD1000PD150 | MaximIC | 5-tap silicon delay line |
